Either a tail light or a separate light shall be so constructed and placed as to illuminate with a white light the rear registration plate, when such registration plate is required, and render it legible from a distance of fifty feet to the rear. May 06, 2007 License plate light is required. It most cases it falls under the same law as tail lights. The license plate must be illuminated by a white or red light, that is visible from a certain distance. Jun 02, 2018 Every passenger car, bus and truck under 80 inches in overall width must be equipped with a lamp so constructed and placed as to illuminate with a white light the rear registration or license plate and render it clearly legible from a distance of 50 feet to the rear.
- License Plate Light Required In Texas
- Is A License Plate Light Required By Law
- Are License Plate Lights Required By Law
- Texas License Plate Light Required
- Rear License Plate Light
- License Plate Light Law
The bulb must have a 'DOT' or appropriate SAE stamp on it. Currently, there are NO DOT approved 'Red' bulbs.
- Vehicles that are equipped from the manufacturer with approved lenses which are clear and lighted by red L.E.D. lights will pass state inspection.
- Vehicles that are equipped with aftermarket lenses which are clear and lighted by a red bulb will be rejected. (Currently, there are NO DOT approved 'Red' bulbs.)
Vehicle lighting equipment is covered in Chapter 547 of the Texas Transportation Code, Subchapter D. § 547.3215 - Use of Federal Standard. Unless specifically prohibited by this chapter, lighting, reflective devices, and associated equipment on a vehicle or motor vehicle must comply with:
- The current federal standards in 49 C.F.R. Section 571.108; or
- The federal standards in that section in effect, if any, at the time the vehicle or motor vehicle was manufactured.
The CFR will refer you to Society of Automotive Engineers (SAE) #J578, which will refer to several other SAE standards. Everything that complies with those standards is 'legal'.
Equipment manufacturers have to self-certify that they meet these standards. DOT does not test equipment unless they act against those who don't meet standards. You should insure that the equipment vendor is reputable and that all equipment has a DOT or appropriate SAE stamp on it (or if not marked, keep the box that it comes in which says it is 'DOT approved') and under no circumstances use equipment that is for 'off-road or show only'.
References:
DescriptionCSCsx86872A DID does not register when Service Provider SIP trunk configuration is loaded from different PCs.Symptom Some Day2 additions or modifications under Telephony are misconfigured for a custom SIP Provider. If instructed to install a later version of phone firmware to resolve a support issue, use the CCA Phone Load Management window or drag-and-drop phone upgrade feature to install the phone firmware.This most recent list of phone firmware loads is located at.
$82.22 - $99.24
The license plate lights on a vehicle are for just that, they light up the area on the back of the vehicle so that people can see the license plate. In most states, it is against the law not to have the license plate illuminated on a vehicle that was equipped with lights from the factory. Some states will even require lights to be added to vehicles that did not come with them from the factory. Purchasing a good quality license plate light will reduce the number of times you need to replace it in the future.
Replacing a license plate light bulb is completed by either removing a lens cover to access the bulb, or by accessing the bulb socket from the interior of the car. The latter is usually going to use an access point in the trunk area. Both methods will be covered below.
Method 1 of 2: Replacing a license plate light bulb with a lens cover
Materials needed
- Replacement bulb
- Screwdriver set
Step 1: Remove the license plate light lens cover. Iolo system mechanic free version. Remove the hardware holding the license plate light lens cover in place. Carefully remove the lens cover.
Step 2: Remove the bulb from the socket. Carefully reach in and pull the old bulb out, being careful not to break the glass.
Step 2: Compare the replacement bulb to the one you removed. It should be the same size and have the same type of contacts.
Step 4: Install the replacement bulb. Place the new bulb into the bulb socket.
Step 5: Turn the headlight switch on. Before reassembling the license plate light assembly, turn the headlight switch on to verify the function of the replacement bulb.
Step 6: Reinstall the license plate light lens cover. Place the license plate lens cover back into place and reinstall the hardware that was removed during the disassembly process.
Method 2 of 2: Replacing a license plate light bulb without a lens cover
Materials needed
- Replacement bulb
- Screwdriver set
Step 1: Open the trunk. Open the trunk to gain access to the area behind the license plate.
Step 2: Pull back the trim carpet. Remove the trim carpet that covers the metal panel that the license plate is mounted to, as in the picture above. This may require the removal of push pins, trim screws, or the weather strip around the trunk.
Step 2: Remove the license plate light bulb socket. This usually requires the socket to be rotated one-fourth to one-half turn in a counterclockwise direction.
Step 4: Remove the license plate light bulb. Gently pinch the bulb with your fingers, being careful not to crush the glass. Then gently pull out on the bulb.
License Plate Light Required In Texas
Step 5: Compare the replacement license plate light bulb to the one you removed. It should be the same physical dimensions and have the same type of base for connection.
Is A License Plate Light Required By Law
Step 6: Install the replacement license plate light bulb. It should go in the same way that the other one came out. Just push the new one into place with light pressure to seat it into the socket.
Are License Plate Lights Required By Law
With the bulb installed in the socket, reinstall the socket into the housing and turn it the required one-fourth to one-half turn it took to remove it, only this time, you will turn it in a clockwise direction.
Step 7: Turn the headlight switch on. Before reassembling the license plate light assembly, turn the headlight switch on to verify the function of the replacement bulb.
Step 8: Reinstall the trim carpet. Put back the trim carpet that was removed to gain access to the license plate light bulb. Be sure to reinstall any hardware that needed to be removed to get to the carpet edges
A license plate light might not be considered a safety feature directly, but it can help other drivers see you on the road. And, as stated above, it is typically required to have the license plate lights working by most municipalities.
Texas License Plate Light Required
If at any point you feel you could use a hand with replacing a license plate light bulb on your vehicle, contact a professional technician, such as those available at YourMechanic. YourMechanic has trained and certified repair professionals that can come to your home or workplace and perform the repairs for you.
Rear License Plate Light
Next Step
License Plate Light Law
Schedule License Plate Light Replacement
These are the light bulbs that illuminate your car’s front and rear license plates. Some cars have one per plate; others have two. Traditionally, they have been incandescent; i.e., lit by heating the filament. These bulbs are inexpensive and provide good clean light. However, they die quickly an.. LEARN MORE
SEE PRICING & SCHEDULING